Re: [Crash-utility] ARM: crash registers might be read from the wrong physical address
What I see is the following:
crash> p crash_notes
crash_notes = $29 = (note_buf_t *) 0xf662e000
crash> p/x __per_cpu_offset
$31 = {0x39b2000, 0x39ba000, 0x39c2000, 0x39ca000}
0xf662e000 + 0x39b2000 = 0xf9fe0000 which is the address seen in readmem.
These are the interesting lines I see in source code (both newer and older kernels):
note_buf_t *crash_notes;
crash_notes = alloc_percpu(note_buf_t);
I do not really understand this in detail, but it seems that alloc_percpu uses
"chunks" and may allocate new chunks if there is not enough memory in the
currently available chunks. So what might have happen is in older cases there is space in
first(??) chunk, while in the newer case a new chunk have to be allocated.
Jan
Jan Karlsson
Senior Software Engineer
MIB
Sony Mobile Communications
Tel: +46703062174
sonymobile.com
-----Original Message-----
From: crash-utility-bounces(a)redhat.com [mailto:crash-utility-bounces@redhat.com] On Behalf
Of Dave Anderson
Sent: torsdag den 19 juli 2012 14:42
To: Discussion list for crash utility usage, maintenance and development
Cc: Fänge, Thomas
Subject: Re: [Crash-utility] ARM: crash registers might be read from the wrong physical
address
----- Original Message -----
These are the same lines in my case.
<readmem: c0d2af6c, KVADDR, "crash_notes", 4, (ROE), 85ba84c>
<read_kdump: addr: c0d2af6c paddr: 80f2af6c cnt: 4>
<readmem: f9fe0000, KVADDR, "note_buf_t", 560, (ROE), 85bac40> <---
!!
<readmem: c0004000, KVADDR, "pgd page", 16384, (FOE), 914e8d0>
I have never seen this problem before, so the behavior you see is
exactly what I have seen before. However with a fairly new kernel I
did not get the correct crash_notes. The investigation lead to the
patch for the problem described in my previous mail.
I have not investigated if there is any patch in newer kernels that
changes this behavior and in that case where it comes from (it could
be a patch by us). However as the algorithm for reading crash_notes is
wrong, as it depends on a variable that is not yet initialized, I
think it should be corrected anyhow. I have tested my patch with both
newer and older kernels and it works as intended.
OK, good. And so apparently the per-cpu region has been moved up into vmalloc space.
I'll queue the change into crash-6.0.9.
For curiosity's sake, can you show me the per-cpu symbol list? In my sample ARM
kernel, it's located in the unity-mapped region just below the .text section, and can
be seen like this:
crash> sym -l
... [ cut ] ...
c004e000 (d) .data..percpu
c004e000 (D) __per_cpu_load
c004e000 (D) __per_cpu_start
c004e000 (D) cpu_data
c004e040 (d) percpu_clockevent
c004e098 (D) current_kprobe
c004e09c (D) kprobe_ctlblk
c004e130 (d) bp_on_reg
c004e170 (d) wp_on_reg
c004e1b0 (D) mmu_gathers
c004e1c0 (D) current_mm
c004e1e0 (D) kstat
... [ cut ] ...
c004f0b4 (d) xmit_recursion
c004f0b8 (d) rt_cache_stat
c004f100 (d) runqueues
c004f620 (d) gcwq_nr_running
c004f640 (d) cfd_data
c004f660 (d) call_single_queue
c004f6a0 (d) csd_data
c004f6c0 (D) softnet_data
c004f7a0 (D) __per_cpu_end
c0050000 (t) .text
...
Your newer kernel must move it up to ~fxxxxxxx?
Thanks,
Dave
--
Crash-utility mailing list
Crash-utility(a)redhat.com
https://www.redhat.com/mailman/listinfo/crash-utility