Re: [Crash-utility] Kernel Crash Analysis on Android
by Shankar, AmarX
Hi Dave,
Thanks for your info regarding kexec tool.
I am unable to download kexec from below link.
http://www.kernel.org/pub/linux/kernel/people/horms/kexec-tools/kexec-too...
It says HTTP 404 Page Not Found.
Could you please guide me on this?
Thanks & Regards,
Amar Shankar
> On Wed, Mar 21, 2012 at 06:00:00PM +0000, Shankar, AmarX wrote:
>
> > I want to do kernel crash Analysis on Android Merrifield Target.
> >
> > Could someone please help me how to do it?
>
> Merrifield is pretty much similar than Medfield, e.g it has x86 core. So I
> guess you can follow the instructions how to setup kdump on x86 (see
> Documentation/kdump/kdump.txt) unless you already have that configured.
>
> crash should support this directly presuming you have vmlinux/vmcore files to
> feed it. You can configure crash to support x86 on x86_64 host by running:
>
> % make target=X86
> & make
>
> (or something along those lines).
Right -- just the first make command will suffice, i.e., when running
on an x86_64 host:
$ wget http://people.redhat.com/anderson/crash-6.0.4.tar.gz
$ tar xzf crash-6.0.4.tar.gz
...
$ cd crash-6.0.4
$ make target=X86
...
$ ./crash <path-to>/vmlinux <path-to>/vmcore
Dave
From: Shankar, AmarX
Sent: Wednesday, March 21, 2012 11:30 PM
To: 'crash-utility(a)redhat.com'
Subject: Kernel Crash Analysis on Android
Hi,
I want to do kernel crash Analysis on Android Merrifield Target.
Could someone please help me how to do it?
Thanks & Regards,
Amar Shankar
11 months
[PATCH] kmem, snap: iomem/ioport display and vmcore snapshot support
by HATAYAMA Daisuke
Some days ago I was in a situation that I had to convert vmcore in
kvmdump format into ELF since some extension module we have locally
can be used only on relatively old crash utility, around version 4,
but such old crash utility cannot handle kvmdump format.
To do the conversion in handy, I used snap command with some modifications
so that it tries to use iomem information in vmcore instead of host's
/proc/iomem. This patch is its cleaned-up version.
In this development, I naturally got down to also making an interface
for an access to resource objects, and so together with the snap
command's patch, I also extended kmem command for iomem/ioport
support. Actually:
kmem -r displays /proc/iomem
crash> kmem -r
00000000-0000ffff : reserved
00010000-0009dbff : System RAM
0009dc00-0009ffff : reserved
000c0000-000c7fff : Video ROM
...
and kmem -R displays /proc/ioport
crash> kmem -R
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
...
Looking into old version of kernel source code back, resource structure
has been unchanged since linux-2.4.0. I borrowed the way of walking on
resouce tree in this patch from the lastest v3.3-rc series, but I
guess the logic is also applicable to old kernels. I expect Dave's
regression testsuite.
Also, there would be another command more sutable for iomem/ioport.
If necessay, I'll repost the patch.
---
HATAYAMA Daisuke (4):
Add vmcore snapshot support
Add kmem -r and -R options
Add dump iomem/ioport functions; a helper for resource objects
Add a helper function for iterating resource objects
defs.h | 9 ++++
extensions/snap.c | 54 ++++++++++++++++++++++-
help.c | 2 +
memory.c | 122 +++++++++++++++++++++++++++++++++++++++++++++++++++--
4 files changed, 180 insertions(+), 7 deletions(-)
--
Thanks.
HATAYAMA Daisuke
11 months
Re: [Crash-utility] question about phys_base
by Dave Anderson
----- Original Message -----
> >
> > OK, so then I don't understand what you mean by "may be the same"?
> >
> > You didn't answer my original question, but if I understand you correctly,
> > it would be impossible for the qemu host to create a PT_LOAD segment that
> > describes an x86_64 guest's __START_KERNEL_map region, because the host
> > doesn't know that what kind of kernel the guest is running.
>
> Yes. Even if the guest is linux, it is still impossible to do it. Because
> the guest maybe in the second kernel.
>
> qemu-dump walks all guest's page table and collect virtual address and
> physical address mapping. If the page is not used by guest, the virtual is set
> to 0. I create PT_LOAD according to such mapping. So if the guest is linux,
> there may be a PT_LOAD segment that describes __START_KERNEL_map region.
> But the information stored in PT_LOAD maybe for the second kernel. If crash
> uses it, crash will see the second kernel, not the first kernel.
Just to be clear -- what do you mean by the "second" kernel? Do you
mean that a guest kernel crashed guest, and did a kdump operation,
and that second kdump kernel failed somehow, and now you're trying
to do a "virsh dump" on the kdump kernel?
Dave
11 months
question about phys_base
by Wen Congyang
Hi, Dave
I am implementing a new dump command in the qemu. The vmcore's
format is elf(like kdump). And I try to provide phys_base in
the PT_LOAD. But if the os uses the first vcpu do kdump, the
value of phys_base is wrong.
I find a function x86_64_virt_phys_base() in crash's code.
Is it OK to call this function first? If the function
successes, we do not calculate phys_base according to PT_LOAD.
Thanks
Wen Congyang
11 months
[PATCH] runq: search current task's runqueue explicitly
by HATAYAMA Daisuke
Currently, runq sub-command doesn't consider CFS runqueue's current
task removed from CFS runqueue. Due to this, the remaining CFS
runqueus that follow the current task's is not displayed. This patch
fixes this by making runq sub-command search current task's runqueue
explicitly.
Note that CFS runqueue exists for each task group, and so does CFS
runqueue's current task, and the above search needs to be done
recursively.
Test
====
On vmcore I made 7 task groups:
root group --- A --- AA --- AAA
+ +- AAB
|
+- AB --- ABA
+- ABB
and then I ran three CPU bound tasks, which is exactly the same as
int main(void) { for (;;) continue; return 0; }
for each task group, including root group; so total 24 tasks. For
readability, I annotated each task name with its belonging group name.
For example, loop.ABA belongs to task group ABA.
Look at CPU0 collumn below. [before] lacks 8 tasks and [after]
successfully shows all tasks on the runqueue, which is identical to
the result of [sched debug] that is expected to ouput correct result.
I'll send this vmcore later.
[before]
crash> runq | cat
CPU 0 RUNQUEUE: ffff88000a215f80
CURRENT: PID: 28263 TASK: ffff880037aaa040 COMMAND: "loop.ABA"
RT PRIO_ARRAY: ffff88000a216098
[no tasks queued]
CFS RB_ROOT: ffff88000a216010
[120] PID: 28262 TASK: ffff880037cc40c0 COMMAND: "loop.ABA"
<cut>
[after]
crash_fix> runq
CPU 0 RUNQUEUE: ffff88000a215f80
CURRENT: PID: 28263 TASK: ffff880037aaa040 COMMAND: "loop.ABA"
RT PRIO_ARRAY: ffff88000a216098
[no tasks queued]
CFS RB_ROOT: ffff88000a216010
[120] PID: 28262 TASK: ffff880037cc40c0 COMMAND: "loop.ABA"
[120] PID: 28271 TASK: ffff8800787a8b40 COMMAND: "loop.ABB"
[120] PID: 28272 TASK: ffff880037afd580 COMMAND: "loop.ABB"
[120] PID: 28245 TASK: ffff8800785e8b00 COMMAND: "loop.AB"
[120] PID: 28246 TASK: ffff880078628ac0 COMMAND: "loop.AB"
[120] PID: 28241 TASK: ffff880078616b40 COMMAND: "loop.AA"
[120] PID: 28239 TASK: ffff8800785774c0 COMMAND: "loop.AA"
[120] PID: 28240 TASK: ffff880078617580 COMMAND: "loop.AA"
[120] PID: 28232 TASK: ffff880079b5d4c0 COMMAND: "loop.A"
<cut>
[sched debug]
crash> runq -d
CPU 0
[120] PID: 28232 TASK: ffff880079b5d4c0 COMMAND: "loop.A"
[120] PID: 28239 TASK: ffff8800785774c0 COMMAND: "loop.AA"
[120] PID: 28240 TASK: ffff880078617580 COMMAND: "loop.AA"
[120] PID: 28241 TASK: ffff880078616b40 COMMAND: "loop.AA"
[120] PID: 28245 TASK: ffff8800785e8b00 COMMAND: "loop.AB"
[120] PID: 28246 TASK: ffff880078628ac0 COMMAND: "loop.AB"
[120] PID: 28262 TASK: ffff880037cc40c0 COMMAND: "loop.ABA"
[120] PID: 28263 TASK: ffff880037aaa040 COMMAND: "loop.ABA"
[120] PID: 28271 TASK: ffff8800787a8b40 COMMAND: "loop.ABB"
[120] PID: 28272 TASK: ffff880037afd580 COMMAND: "loop.ABB"
<cut>
Diff stat
=========
defs.h | 1 +
task.c | 37 +++++++++++++++++--------------------
2 files changed, 18 insertions(+), 20 deletions(-)
Thanks.
HATAYAMA, Daisuke
11 months
[RFC] makedumpfile, crash: LZO compression support
by HATAYAMA Daisuke
Hello,
This is a RFC patch set that adds LZO compression support to
makedumpfile and crash utility. LZO is as good as in size but by far
better in speed than ZLIB, leading to reducing down time during
generation of crash dump and refiltering.
How to build:
1. Get LZO library, which is provided as lzo-devel package on recent
linux distributions, and is also available on author's website:
http://www.oberhumer.com/opensource/lzo/.
2. Apply the patch set to makedumpfile v1.4.0 and crash v6.0.0.
3. Build both using make. But for crash, do the following now:
$ make CFLAGS="-llzo2"
How to use:
I've newly used -l option for lzo compression in this patch. So for
example, do as follows:
$ makedumpfile -l vmcore dumpfile
$ crash vmlinux dumpfile
Request of configure-like feature for crash utility:
I would like configure-like feature on crash utility for users to
select wheather to add LZO feature actually or not in build-time,
that is: ./configure --enable-lzo or ./configure --disable-lzo.
The reason is that support staff often downloads and installs the
latest version of crash utility on machines where lzo library is not
provided.
Looking at the source code, it looks to me that crash does some kind
of configuration processing in a local manner, around configure.c,
and I guess it's difficult to use autoconf tools directly.
Or is there another better way?
Performance Comparison:
Sample Data
Ideally, I must have measured the performance for many enough
vmcores generated from machines that was actually running, but now
I don't have enough sample vmcores, I couldn't do so. So this
comparison doesn't answer question on I/O time improvement. This
is TODO for now.
Instead, I choosed worst and best cases regarding compression
ratio and speed only. Specifically, the former is /dev/urandom and
the latter is /dev/zero.
I get the sample data of 10MB, 100MB and 1GB by doing like this:
$ dd bs=4096 count=$((1024*1024*1024/4096)) if=/dev/urandom of=urandom.1GB
How to measure
Then I performed compression for each block, 4096 bytes, and
measured total compression time and output size. See attached
mycompress.c.
Result
See attached file result.txt.
Discussion
For both kinds of data, lzo's compression was considerably quicker
than zlib's. Compression ratio is about 37% for urandom data, and
about 8.5% for zero data. Actual situation of physical memory
would be in between the two cases, and so I guess average
compression time ratio is between 37% and 8.5%.
Although beyond the topic of this patch set, we can estimate worst
compression time on more data size since compression is performed
block size wise and the compression time increases
linearly. Estimated worst time on 2TB memory is about 15 hours for
lzo and about 40 hours for zlib. In this case, compressed data
size is larger than the original, so they are really not used,
compression time is fully meaningless. I think compression must be
done in parallel, and I'll post such patch later.
Diffstat
* makedumpfile
diskdump_mod.h | 3 +-
makedumpfile.c | 98 +++++++++++++++++++++++++++++++++++++++++++++++++------
makedumpfile.h | 12 +++++++
3 files changed, 101 insertions(+), 12 deletions(-)
* crash
defs.h | 1 +
diskdump.c | 20 +++++++++++++++++++-
diskdump.h | 3 ++-
3 files changed, 22 insertions(+), 2 deletions(-)
TODO
* evaluation including I/O time using actual vmcores
Thanks.
HATAYAMA, Daisuke
11 months
Re: [Crash-utility] [RFI] Support Fujitsu's sadump dump format
by tachibana@mxm.nes.nec.co.jp
Hi Hatayama-san,
On 2011/06/29 12:12:18 +0900, HATAYAMA Daisuke <d.hatayama(a)jp.fujitsu.com> wrote:
> From: Dave Anderson <anderson(a)redhat.com>
> Subject: Re: [Crash-utility] [RFI] Support Fujitsu's sadump dump format
> Date: Tue, 28 Jun 2011 08:57:42 -0400 (EDT)
>
> >
> >
> > ----- Original Message -----
> >> Fujitsu has stand-alone dump mechanism based on firmware level
> >> functionality, which we call SADUMP, in short.
> >>
> >> We've maintained utility tools internally but now we're thinking that
> >> the best is crash utility and makedumpfile supports the sadump format
> >> for the viewpoint of both portability and maintainability.
> >>
> >> We'll be of course responsible for its maintainance in a continuous
> >> manner. The sadump dump format is very similar to diskdump format and
> >> so kdump (compressed) format, so we estimate patch set would be a
> >> relatively small size.
> >>
> >> Could you tell me whether crash utility and makedumpfile can support
> >> the sadump format? If OK, we'll start to make patchset.
I think it's not bad to support sadump by makedumpfile. However I have
several questions.
- Do you want to use makedumpfile to make an existing file that sadump has
dumped small?
- It isn't possible to support the same form as kdump-compressed format
now, is it?
- When the information that makedumpfile reads from a note of /proc/vmcore
(or a header of kdump-compressed format) is added by an extension of
makedumpfile, do you need to modify sadump?
Thanks
tachibana
> >
> > Sure, yes, the crash utility can always support another dumpfile format.
> >
>
> Thanks. It helps a lot.
>
> > It's unclear to me how similar SADUMP is to diskdump/compressed-kdump.
> > Does your internal version patch diskdump.c, or do you maintain your
> > own "sadump.c"? I ask because if your patchset is at all intrusive,
> > I'd prefer it be kept in its own file, primarily for maintainability,
> > but also because SADUMP is essentially a black-box to anybody outside
> > Fujitsu.
>
> What I meant when I used ``similar'' is both literally and
> logically. The format consists of diskdump header-like header, two
> kinds of bitmaps used for the same purpose as those in diskump format,
> and memory data. They can be handled in common with the existing data
> structure, diskdump_data, non-intrusively, so I hope they are placed
> in diskdump.c.
>
> On the other hand, there's a code to be placed at such specific
> area. sadump is triggered depending on kdump's progress and so
> register values to be contained in vmcore varies according to the
> progress: If crash_notes has been initialized when sadump is
> triggered, sadump packs the register values in crash_notes; if not
> yet, packs registers gathered by firmware. This is sadump specific
> processing, so I think putting it in specific sadump.c file is a
> natural and reasonable choise.
>
> Anyway, I have not made any patch set for this. I'll post a patch set
> when I complete.
>
> Again, thanks a lot for the positive answer.
>
> Thanks.
> HATAYAMA, Daisuke
>
>
> _______________________________________________
> kexec mailing list
> kexec(a)lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/kexec
11 months
[PATCH 0/5] [RFC] Multi-thread support for search cmd
by Tao Liu
The primary part of the patchset will introduce multithread support for search
cmd to improve its performance. A search operation is mainly made up with 2
steps: 1) readmem data into pagebuf, 2) search specific values within the
pagebuf. A typical workflow of search is as follows:
for addr from low to high:
do
readmem(addr, pagebuf)
search_value(value, pagebuf)
addr += pagesize
done
There are 2 points which we can accelerate: 1) readmem don't have to wait
search_value, when search_value is working, readmem can read the next pagebuf
at the same time. 2) higher addr don't have to wait lower addr, they can be
processed at the same time if we carefully arrange the output order.
For point 1, we introduce zones for pagebuf, e.g. search_value can work on
zone 0 while readmem can prepare the data for zone 1. For point 2, we introduce
multiple search_value in threads, e.g. readmem will prepare 100 pages as a
batch, then we will have 4 threads of search_value, thread 0 handles page 1~25,
thread 2 handles page 26~50 page, thread 3 handles page 51~75, thread 4 handles
page 76~100.
A typical workflow of multithread search implemented in this patchset is as
follows, which removed thread synchronization:
pagebuf[ZONE][BATCH]
zone_index = buf_index = 0
create_thread(4, search_value)
for addr from low to high:
do
if buf_index < BATCH
readmem(addr, pagebuf[zone_index][buf_index++])
addr += pagesize
else
start_thread(pagebuf[zone_index], 0/4 * BATCH, 1/4 * BATCH)
start_thread(pagebuf[zone_index], 1/4 * BATCH, 2/4 * BATCH)
start_thread(pagebuf[zone_index], 2/4 * BATCH, 3/4 * BATCH)
start_thread(pagebuf[zone_index], 3/4 * BATCH, 4/4 * BATCH)
zone_index++
buf_index = 0
fi
done
readmem works in the main process and not multi-threaded, because readmem will
not only read data from vmcore, decompress it, but walk through page tables if
virtual address given. It is hard to reimplement it into thread safe version,
search_value is easier to be made thread-safe. By carefully choose batch size
and thread num, we can maximize the concurrency.
The last part of the patchset, is replacing lseek/read to pread for kcore and
diskdumped vmcore.
Here is the performance test result chart. Please note the vmcore and
kcore are tested seperately on 2 different machines. crash-orig is the
crash compiled with clean upstream code, crash-pread is the code with only
pread patch applied(patch 5), crash-multi is the code with only multithread
patches applied(patch 1~4).
ulong search:
$ time echo "search abcd" | ./crash-orig vmcore vmlinux > /dev/null
$ time echo "search abcd -f 4 -n 4" | ./crash-multi vmcore vmlinux > /dev/null
45G vmcore 64G kcore
real user sys real user sys
crash-orig 16m56.595s 15m57.188s 0m56.698s 1m37.982s 0m51.625s 0m46.266s
crash-pread 16m46.366s 15m55.790s 0m48.894s 1m9.179s 0m36.646s 0m32.368s
crash-multi 16m26.713s 19m8.722s 1m29.263s 1m27.661s 0m57.789s 0m54.604s
string search:
$ time echo "search -c abcddbca" | ./crash-orig vmcore vmlinux > /dev/null
$ time echo "search -c abcddbca -f 4 -n 4" | ./crash-multi vmcore vmlinux > /dev/null
45G vmcore 64G kcore
real user sys real user sys
crash-orig 33m33.481s 32m38.321s 0m52.771s 8m32.034s 7m50.050s 0m41.478s
crash-pread 33m25.623s 32m35.019s 0m47.394s 8m4.347s 7m35.352s 0m28.479s
crash-multi 16m31.016s 38m27.456s 1m11.048s 5m11.725s 7m54.224s 0m44.186s
Discussion:
1) Either multithread and pread patches can improve the performance a
bit, so if both patches applied, the performance can be better.
2) Multi-thread search performs much better in search time consumptive
tasks, such as string search.
Tao Liu (5):
Introduce multi-thread to search_virtual
Introduce multi-thread to search_physical
Introduce multi-thread to string search
Introduce multi-thread options to search cmd
Replace lseek/read into pread for kcore and vmcore reading.
defs.h | 6 +
diskdump.c | 11 +-
help.c | 17 +-
memory.c | 1176 +++++++++++++++++++++++++++++++++++++++++-----------
netdump.c | 5 +-
task.c | 14 +
6 files changed, 969 insertions(+), 260 deletions(-)
--
2.33.1
1 year, 6 months