Re: [Crash-utility] Kernel Crash Analysis on Android
by Shankar, AmarX
Hi Dave,
Thanks for your info regarding kexec tool.
I am unable to download kexec from below link.
http://www.kernel.org/pub/linux/kernel/people/horms/kexec-tools/kexec-too...
It says HTTP 404 Page Not Found.
Could you please guide me on this?
Thanks & Regards,
Amar Shankar
> On Wed, Mar 21, 2012 at 06:00:00PM +0000, Shankar, AmarX wrote:
>
> > I want to do kernel crash Analysis on Android Merrifield Target.
> >
> > Could someone please help me how to do it?
>
> Merrifield is pretty much similar than Medfield, e.g it has x86 core. So I
> guess you can follow the instructions how to setup kdump on x86 (see
> Documentation/kdump/kdump.txt) unless you already have that configured.
>
> crash should support this directly presuming you have vmlinux/vmcore files to
> feed it. You can configure crash to support x86 on x86_64 host by running:
>
> % make target=X86
> & make
>
> (or something along those lines).
Right -- just the first make command will suffice, i.e., when running
on an x86_64 host:
$ wget http://people.redhat.com/anderson/crash-6.0.4.tar.gz
$ tar xzf crash-6.0.4.tar.gz
...
$ cd crash-6.0.4
$ make target=X86
...
$ ./crash <path-to>/vmlinux <path-to>/vmcore
Dave
From: Shankar, AmarX
Sent: Wednesday, March 21, 2012 11:30 PM
To: 'crash-utility(a)redhat.com'
Subject: Kernel Crash Analysis on Android
Hi,
I want to do kernel crash Analysis on Android Merrifield Target.
Could someone please help me how to do it?
Thanks & Regards,
Amar Shankar
10 months, 1 week
[PATCH] kmem, snap: iomem/ioport display and vmcore snapshot support
by HATAYAMA Daisuke
Some days ago I was in a situation that I had to convert vmcore in
kvmdump format into ELF since some extension module we have locally
can be used only on relatively old crash utility, around version 4,
but such old crash utility cannot handle kvmdump format.
To do the conversion in handy, I used snap command with some modifications
so that it tries to use iomem information in vmcore instead of host's
/proc/iomem. This patch is its cleaned-up version.
In this development, I naturally got down to also making an interface
for an access to resource objects, and so together with the snap
command's patch, I also extended kmem command for iomem/ioport
support. Actually:
kmem -r displays /proc/iomem
crash> kmem -r
00000000-0000ffff : reserved
00010000-0009dbff : System RAM
0009dc00-0009ffff : reserved
000c0000-000c7fff : Video ROM
...
and kmem -R displays /proc/ioport
crash> kmem -R
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
...
Looking into old version of kernel source code back, resource structure
has been unchanged since linux-2.4.0. I borrowed the way of walking on
resouce tree in this patch from the lastest v3.3-rc series, but I
guess the logic is also applicable to old kernels. I expect Dave's
regression testsuite.
Also, there would be another command more sutable for iomem/ioport.
If necessay, I'll repost the patch.
---
HATAYAMA Daisuke (4):
Add vmcore snapshot support
Add kmem -r and -R options
Add dump iomem/ioport functions; a helper for resource objects
Add a helper function for iterating resource objects
defs.h | 9 ++++
extensions/snap.c | 54 ++++++++++++++++++++++-
help.c | 2 +
memory.c | 122 +++++++++++++++++++++++++++++++++++++++++++++++++++--
4 files changed, 180 insertions(+), 7 deletions(-)
--
Thanks.
HATAYAMA Daisuke
10 months, 1 week
Re: [Crash-utility] question about phys_base
by Dave Anderson
----- Original Message -----
> >
> > OK, so then I don't understand what you mean by "may be the same"?
> >
> > You didn't answer my original question, but if I understand you correctly,
> > it would be impossible for the qemu host to create a PT_LOAD segment that
> > describes an x86_64 guest's __START_KERNEL_map region, because the host
> > doesn't know that what kind of kernel the guest is running.
>
> Yes. Even if the guest is linux, it is still impossible to do it. Because
> the guest maybe in the second kernel.
>
> qemu-dump walks all guest's page table and collect virtual address and
> physical address mapping. If the page is not used by guest, the virtual is set
> to 0. I create PT_LOAD according to such mapping. So if the guest is linux,
> there may be a PT_LOAD segment that describes __START_KERNEL_map region.
> But the information stored in PT_LOAD maybe for the second kernel. If crash
> uses it, crash will see the second kernel, not the first kernel.
Just to be clear -- what do you mean by the "second" kernel? Do you
mean that a guest kernel crashed guest, and did a kdump operation,
and that second kdump kernel failed somehow, and now you're trying
to do a "virsh dump" on the kdump kernel?
Dave
10 months, 1 week
question about phys_base
by Wen Congyang
Hi, Dave
I am implementing a new dump command in the qemu. The vmcore's
format is elf(like kdump). And I try to provide phys_base in
the PT_LOAD. But if the os uses the first vcpu do kdump, the
value of phys_base is wrong.
I find a function x86_64_virt_phys_base() in crash's code.
Is it OK to call this function first? If the function
successes, we do not calculate phys_base according to PT_LOAD.
Thanks
Wen Congyang
10 months, 1 week
[PATCH] runq: search current task's runqueue explicitly
by HATAYAMA Daisuke
Currently, runq sub-command doesn't consider CFS runqueue's current
task removed from CFS runqueue. Due to this, the remaining CFS
runqueus that follow the current task's is not displayed. This patch
fixes this by making runq sub-command search current task's runqueue
explicitly.
Note that CFS runqueue exists for each task group, and so does CFS
runqueue's current task, and the above search needs to be done
recursively.
Test
====
On vmcore I made 7 task groups:
root group --- A --- AA --- AAA
+ +- AAB
|
+- AB --- ABA
+- ABB
and then I ran three CPU bound tasks, which is exactly the same as
int main(void) { for (;;) continue; return 0; }
for each task group, including root group; so total 24 tasks. For
readability, I annotated each task name with its belonging group name.
For example, loop.ABA belongs to task group ABA.
Look at CPU0 collumn below. [before] lacks 8 tasks and [after]
successfully shows all tasks on the runqueue, which is identical to
the result of [sched debug] that is expected to ouput correct result.
I'll send this vmcore later.
[before]
crash> runq | cat
CPU 0 RUNQUEUE: ffff88000a215f80
CURRENT: PID: 28263 TASK: ffff880037aaa040 COMMAND: "loop.ABA"
RT PRIO_ARRAY: ffff88000a216098
[no tasks queued]
CFS RB_ROOT: ffff88000a216010
[120] PID: 28262 TASK: ffff880037cc40c0 COMMAND: "loop.ABA"
<cut>
[after]
crash_fix> runq
CPU 0 RUNQUEUE: ffff88000a215f80
CURRENT: PID: 28263 TASK: ffff880037aaa040 COMMAND: "loop.ABA"
RT PRIO_ARRAY: ffff88000a216098
[no tasks queued]
CFS RB_ROOT: ffff88000a216010
[120] PID: 28262 TASK: ffff880037cc40c0 COMMAND: "loop.ABA"
[120] PID: 28271 TASK: ffff8800787a8b40 COMMAND: "loop.ABB"
[120] PID: 28272 TASK: ffff880037afd580 COMMAND: "loop.ABB"
[120] PID: 28245 TASK: ffff8800785e8b00 COMMAND: "loop.AB"
[120] PID: 28246 TASK: ffff880078628ac0 COMMAND: "loop.AB"
[120] PID: 28241 TASK: ffff880078616b40 COMMAND: "loop.AA"
[120] PID: 28239 TASK: ffff8800785774c0 COMMAND: "loop.AA"
[120] PID: 28240 TASK: ffff880078617580 COMMAND: "loop.AA"
[120] PID: 28232 TASK: ffff880079b5d4c0 COMMAND: "loop.A"
<cut>
[sched debug]
crash> runq -d
CPU 0
[120] PID: 28232 TASK: ffff880079b5d4c0 COMMAND: "loop.A"
[120] PID: 28239 TASK: ffff8800785774c0 COMMAND: "loop.AA"
[120] PID: 28240 TASK: ffff880078617580 COMMAND: "loop.AA"
[120] PID: 28241 TASK: ffff880078616b40 COMMAND: "loop.AA"
[120] PID: 28245 TASK: ffff8800785e8b00 COMMAND: "loop.AB"
[120] PID: 28246 TASK: ffff880078628ac0 COMMAND: "loop.AB"
[120] PID: 28262 TASK: ffff880037cc40c0 COMMAND: "loop.ABA"
[120] PID: 28263 TASK: ffff880037aaa040 COMMAND: "loop.ABA"
[120] PID: 28271 TASK: ffff8800787a8b40 COMMAND: "loop.ABB"
[120] PID: 28272 TASK: ffff880037afd580 COMMAND: "loop.ABB"
<cut>
Diff stat
=========
defs.h | 1 +
task.c | 37 +++++++++++++++++--------------------
2 files changed, 18 insertions(+), 20 deletions(-)
Thanks.
HATAYAMA, Daisuke
10 months, 1 week
[RFC] makedumpfile, crash: LZO compression support
by HATAYAMA Daisuke
Hello,
This is a RFC patch set that adds LZO compression support to
makedumpfile and crash utility. LZO is as good as in size but by far
better in speed than ZLIB, leading to reducing down time during
generation of crash dump and refiltering.
How to build:
1. Get LZO library, which is provided as lzo-devel package on recent
linux distributions, and is also available on author's website:
http://www.oberhumer.com/opensource/lzo/.
2. Apply the patch set to makedumpfile v1.4.0 and crash v6.0.0.
3. Build both using make. But for crash, do the following now:
$ make CFLAGS="-llzo2"
How to use:
I've newly used -l option for lzo compression in this patch. So for
example, do as follows:
$ makedumpfile -l vmcore dumpfile
$ crash vmlinux dumpfile
Request of configure-like feature for crash utility:
I would like configure-like feature on crash utility for users to
select wheather to add LZO feature actually or not in build-time,
that is: ./configure --enable-lzo or ./configure --disable-lzo.
The reason is that support staff often downloads and installs the
latest version of crash utility on machines where lzo library is not
provided.
Looking at the source code, it looks to me that crash does some kind
of configuration processing in a local manner, around configure.c,
and I guess it's difficult to use autoconf tools directly.
Or is there another better way?
Performance Comparison:
Sample Data
Ideally, I must have measured the performance for many enough
vmcores generated from machines that was actually running, but now
I don't have enough sample vmcores, I couldn't do so. So this
comparison doesn't answer question on I/O time improvement. This
is TODO for now.
Instead, I choosed worst and best cases regarding compression
ratio and speed only. Specifically, the former is /dev/urandom and
the latter is /dev/zero.
I get the sample data of 10MB, 100MB and 1GB by doing like this:
$ dd bs=4096 count=$((1024*1024*1024/4096)) if=/dev/urandom of=urandom.1GB
How to measure
Then I performed compression for each block, 4096 bytes, and
measured total compression time and output size. See attached
mycompress.c.
Result
See attached file result.txt.
Discussion
For both kinds of data, lzo's compression was considerably quicker
than zlib's. Compression ratio is about 37% for urandom data, and
about 8.5% for zero data. Actual situation of physical memory
would be in between the two cases, and so I guess average
compression time ratio is between 37% and 8.5%.
Although beyond the topic of this patch set, we can estimate worst
compression time on more data size since compression is performed
block size wise and the compression time increases
linearly. Estimated worst time on 2TB memory is about 15 hours for
lzo and about 40 hours for zlib. In this case, compressed data
size is larger than the original, so they are really not used,
compression time is fully meaningless. I think compression must be
done in parallel, and I'll post such patch later.
Diffstat
* makedumpfile
diskdump_mod.h | 3 +-
makedumpfile.c | 98 +++++++++++++++++++++++++++++++++++++++++++++++++------
makedumpfile.h | 12 +++++++
3 files changed, 101 insertions(+), 12 deletions(-)
* crash
defs.h | 1 +
diskdump.c | 20 +++++++++++++++++++-
diskdump.h | 3 ++-
3 files changed, 22 insertions(+), 2 deletions(-)
TODO
* evaluation including I/O time using actual vmcores
Thanks.
HATAYAMA, Daisuke
10 months, 1 week
Re: [Crash-utility] [RFI] Support Fujitsu's sadump dump format
by tachibana＠mxm.nes.nec.co.jp
Hi Hatayama-san,
On 2011/06/29 12:12:18 +0900, HATAYAMA Daisuke <d.hatayama(a)jp.fujitsu.com> wrote:
> From: Dave Anderson <anderson(a)redhat.com>
> Subject: Re: [Crash-utility] [RFI] Support Fujitsu's sadump dump format
> Date: Tue, 28 Jun 2011 08:57:42 -0400 (EDT)
>
> >
> >
> > ----- Original Message -----
> >> Fujitsu has stand-alone dump mechanism based on firmware level
> >> functionality, which we call SADUMP, in short.
> >>
> >> We've maintained utility tools internally but now we're thinking that
> >> the best is crash utility and makedumpfile supports the sadump format
> >> for the viewpoint of both portability and maintainability.
> >>
> >> We'll be of course responsible for its maintainance in a continuous
> >> manner. The sadump dump format is very similar to diskdump format and
> >> so kdump (compressed) format, so we estimate patch set would be a
> >> relatively small size.
> >>
> >> Could you tell me whether crash utility and makedumpfile can support
> >> the sadump format? If OK, we'll start to make patchset.
I think it's not bad to support sadump by makedumpfile. However I have
several questions.
- Do you want to use makedumpfile to make an existing file that sadump has
dumped small?
- It isn't possible to support the same form as kdump-compressed format
now, is it?
- When the information that makedumpfile reads from a note of /proc/vmcore
(or a header of kdump-compressed format) is added by an extension of
makedumpfile, do you need to modify sadump?
Thanks
tachibana
> >
> > Sure, yes, the crash utility can always support another dumpfile format.
> >
>
> Thanks. It helps a lot.
>
> > It's unclear to me how similar SADUMP is to diskdump/compressed-kdump.
> > Does your internal version patch diskdump.c, or do you maintain your
> > own "sadump.c"? I ask because if your patchset is at all intrusive,
> > I'd prefer it be kept in its own file, primarily for maintainability,
> > but also because SADUMP is essentially a black-box to anybody outside
> > Fujitsu.
>
> What I meant when I used ``similar'' is both literally and
> logically. The format consists of diskdump header-like header, two
> kinds of bitmaps used for the same purpose as those in diskump format,
> and memory data. They can be handled in common with the existing data
> structure, diskdump_data, non-intrusively, so I hope they are placed
> in diskdump.c.
>
> On the other hand, there's a code to be placed at such specific
> area. sadump is triggered depending on kdump's progress and so
> register values to be contained in vmcore varies according to the
> progress: If crash_notes has been initialized when sadump is
> triggered, sadump packs the register values in crash_notes; if not
> yet, packs registers gathered by firmware. This is sadump specific
> processing, so I think putting it in specific sadump.c file is a
> natural and reasonable choise.
>
> Anyway, I have not made any patch set for this. I'll post a patch set
> when I complete.
>
> Again, thanks a lot for the positive answer.
>
> Thanks.
> HATAYAMA, Daisuke
>
>
> _______________________________________________
> kexec mailing list
> kexec(a)lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/kexec
10 months, 1 week
list cgroup from crash
by Mathew T
Hi,
I am trying to figure out if I can extract the values associated with
cgroups from kernel crash dump. I can see "cgorup" is mounted when i
issue "mount" command in crash utility. And it shows mount/superblock
address. How can I further dig down and print the values inside cgroup
fs. Suppose if I want to print "/sys/fs/cgroup/cpu.stat" in the crash
utility!? The extension lscgroup / cgget are not working in latest
kernels.
Regards,
Fern
1 year
Are all linux_banner type cases covered in verify_version()?
by David Mair
Hi All,
Before I consider starting work on a patch for this I'd appreciate more
input.
I am seeing random cases of crash failing to load reporting an x86_64
coredump reporting a "bad" linux_banner. However, the value displayed as
the banner is:
0x65762078756e694c
which is plainly ASCII text as a 64-bit number and is the little-endian
reversal of the text "Linux ver".
It's randomly found with specific coredumps and reproduces all times
with that coredump and a given version of crash, though sometimes it
will appear when using a given coredump with one version of crash but
not with another version of crash. What I'm trying to get working is
crash current and the rest of this is experience using crash 8.0.3 only.
I used gdb crash to debug it through verify_version(). If I breakpoint
there with gdb crash and step through the function I find that in the
section:
if (!(sp = symbol_search("linux_banner")))
error(FATAL, "linux_banner symbol does not exist?\n");
else if ((sp->type == 'R') || (sp->type == 'r') ||
(THIS_KERNEL_VERSION >= LINUX(2,6,11) && (sp->type == 'D' || sp->type
== 'd')) ||
(machine_type("ARM") && sp->type == 'T') ||
(machine_type("ARM64")))
linux_banner = symbol_value("linux_banner");
else
get_symbol_data("linux_banner", sizeof(ulong), &linux_banner);
* The if block is not executed, i.e. symbol_search("linux_banner")
succeeded and we have a usable struct syment for "linux_banner" in sp
* The else if block is not executed, all conditions are met or not
relevant except for the the value of sp->type in the case of
THIS_KERNEL_VERSION >= LINUX(2,6,11). But sp->type is 'B', bss segment
* The final else block is executed, we copy sizeof(ulong) bytes of
symbol data from what "linux_banner" refers to into the crash internal
linux_banner variable
Here's how sp looks at the else if statement in the above code:
gdb) print *sp
$2 = {value = 18446744071587233984, name = 0x5555566a735b "linux_banner",
val_hash_next = 0x7fffe51e4338, name_hash_next = 0x7fffe51f8d38,
type = 66 'B', cnt = 1 '\001', flags = 0 '\000', pad2 = 0 '\000'}
...and sp->value in hex is:
(gdb) p/x sp->value
$5 = 0xffffffff818000c0
Starting crash in --minimal mode with the same core, kernel and
debuginfo so that I can try to read 0xffffffff818000c0 I find:
crash> rd 0xffffffff818000c0 18
ffffffff818000c0: 65762078756e694c 2e34206e6f697372 Linux version 4.
ffffffff818000d0: 34392d3038312e34 6665642d3533312e 4.180-94.135-def
ffffffff818000e0: 65672820746c7561 6c697562406f6b65 ault (geeko@buil
ffffffff818000f0: 28202974736f6864 7372657620636367 dhost) (gcc vers
ffffffff81800100: 2e382e34206e6f69 2045535553282035 ion 4.8.5 (SUSE
ffffffff81800110: 29202978756e694c 20504d5320312320 Linux) ) #1 SMP
ffffffff81800120: 20766f4e206e6f4d 35353a3930203631 Mon Nov 16 09:55
ffffffff81800130: 204354552037353a 3033282030323032 :57 UTC 2020 (30
ffffffff81800140: 000a293039393633 0000000000000000 36990)..........
IOW, it is the linux_banner, it's at 0xffffffff818000c0 and if the first
sizeof(ulong) bytes are read into crash's linux_banner variable via
get_symbol_data() it makes a 64-bit number with little-endian revesral
from the string bytes "Linux ver" from the actual linux_banner text, the
same value seen in the error report when crash fails.
If I repeat the above debug of verify_version() in gdb and at the else
if block in the above C in verify_version() I set var the sp->type to be
'D' or 'd' then crash's linux_banner is set to 0xffffffff818000c0
(sp->value) and the else if block is executed then the remainder of the
function successfully finds a linux_banner and gets the version
information from it and crash loads.
In symbol_search() is the value of type in the returned struct syment a
property generated by crash (I thought not and it was based on the
kernel compilation, possible kdummp/makedumpfile but not controlled by
crash)? If I'm correct then is it safe to expect a struct syment with
type 'B' (also 'b' I believe) for linux_banner? Or is there anything
special about a bss segment type that makes it not possible to assume we
can take sp->value as-is for the address of the linux_banner string
details, i.e. we can't safely use symbol_value("linux_banner") to set
the crash linux_banner variable if the struct syment type for
linux_banner is 'B' or 'b'?
Any comments? I'll write a patch if that's the right direction but I
need a better understanding of why symbols with the type bss segment
aren't already assumed valid sources of a linux_banner address value,
only 'D' and 'd' types are and if there is anything special I don't
understand about 'B' and 'b' types.
--
Thanks,
David.
1 year
